《Table 2.Mechanical properties of TiN and Al2O3 inclusions by nanoindentation tests》

《Table 2.Mechanical properties of TiN and Al2O3 inclusions by nanoindentation tests》   提示：宽带有限、当前游客访问压缩模式
本系列图表出处文件名：随高清版一同展现
《Comparison between the surface defects caused by Al_2O_3 and TiN inclusions in interstitial-free steel auto sheets》


  1. 获取 高清版本忘记账户？点击这里登录
  1. 下载图表忘记账户？点击这里登录

The results of nanoindentation tests are shown in Table 2.Because of the smaller size of Ti N，it was difficult for the indenter to absolutely hit the inclusion；therefore，few data were obtained on TiN inclusions，but the results are similar to those of Ref.[11].Table 2 shows that in as-cast and rolled states，the average hardnesses of Al2O3 inclusions were2.935 and 2.528 GPa，respectively，and the hardnesses of Ti N inclusions were 12.200 and 12.603 GPa，respectively.The hardnesses of matrixes in as-cast and rolled states were1.872 and 1.739 GPa，respectively.This shows that the hardnesses of Al2O3 and Ti N inclusions were much higher than that of the matrix，and the hardness of TiN was about 7times as high as that of the matrix.These inclusions tend to cause defects in the rolling process.

图表编号XD0050011800    严禁用于非法目的
绘制时间2019.02.01
作者Rui Wang、Yan-ping Bao、Zhi-jie Yan、Da-zhao Li、Yan Kang
绘制单位School of Materials Science and Engineering, North University of China、State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing、School of Materials Science and Engineering, North University of China、School of Materials Sci
更多格式高清、无水印（增值服务）

相关图表

  1. 《Table 2 Mechanical and physical properties of sintered friction materials》2019.02.01
  2. 《Table 2 Mechanical properties of PEUR-SSx-Ns at original state and after healed:tensile strength (σ) , ultimate elongati》2019.03.01
  3. 《Table 2 Mechanical properties of XNBR and its composites》2019.01.15
  4. 《Table 2.Mechanical properties of the AF and SC samples》2019.01.01
  5. 《表2 环氧树脂和环氧树脂修饰碳纳米管复合材料的力学性能Table 2 Mechanical properties of EP and EP/CNT composite》2018.06.30
  6. 《Table 2 Mechanical properties of NR vulcanizates filled with different amounts of N 90 or N 98》2018.11.15
  7. 《Table 2 Mechanical properties of ACM and hindered phenol/ACM vulcanizates》2018.09.15
  8. 《Table 2 Mechanical properties of natural rubber/silica composites prepared by different methods》2018.07.15
  9. 《表2 EPDM橡胶处理前后的力学性能Table 2 Mechanical properties of EPDM before and after treatment》2018.04.01
  10. 《表3 燃气和液态Al2O3的物性参数Table 3 Physical propertied of fuel gas and Al2O3 (l)》2018.04.01
  11. 《Table 2 Mechanical properties of PP and PP/PS injection-molded bar》2018.02.10
  12. 《表2 合金双级时效后基材和焊接头的力学性能Table 2 Mechanical properties of base metal and welded joint after two-stage aging》2018.04.01
  13. 《表2 不同临界区等温退火时间钢的力学性能和残余奥氏体含量Table 2 Mechanical properties and retained austenite content of the investigated steel of di》2018.03.25
  14. 《表2 粗晶及超细晶工业纯钛的力学性能Table 2 Mechanical properties of coarse-grained and ultrafine grained CP Ti》2018.07.01
  15. 《表2 单级均匀化及双级均匀化处理后成品板材的性能Table 2 Mechanical properties of the plates treated by single/two-stages homogenization》2018.04.01
  16. 《表2 600 MPa级元宝梁开裂件力学性能与冷弯性能Table 2 Mechanical properties and cold bending performance of 600 MPa grade crossbeam crack sa》2018.06.01
  17. 《表2 FB2和1CrMo典型力学性能Table 2 Mechanical properties of FB2and 1CrMo》2018.05.25
  18. 《表2 试件内外钢管材料的基本力学性能参数Table 2 Mechanical properties of outer and inner tubes》2018.01.25
  19. 《表2 GFRP和南方松的力学性能Table 2 Mechanical properties of GFRP and wood》2018.08.28
  20. 《Table 2.Mechanical properties of investigated steels after hot rolling and cooling in air》2018.10.01

随机翻阅

《表3 不同研究变量与手术方式、术中出血量的相关性》 《表3 灵敏度检测结果：丁苯橡胶改性沥青老化前后性能对比分析》 《表1 3 电缆沟槽台车工效对比表》 《表8 印尼规范道路最大纵坡》 《表3 不同级别PCa超声造影参数分析》 《表1 两组观察指标比较[n,±s]》 《表1 二十个开放型职业化社交平台代表》 《表2 两组近期疗效比较 (n=30)》 《表1 0 其他交叉项检验结果》 《表3 犹豫模糊得分矩阵》